Other Products / Services #5146409

Low CostWide Supply Voltage Range: 5V to 40VHigh Output Current: 3A MinimumHigh Efficiency: Vs-2.2V at 2.5AInternal Current LimitWide Common Mode Range(Includes Negative Supply Voltage)Low DistortionInternal Output Snubbers for Ultra-Stable OperationThe MSK 105 is a high power quad operational amplifier. Each amplifier is capable of delivering three amps ofcurrent to the load. The MSK 105 is an excellent low cost alternative for bridge mode configurations since allamplifiers are packaged together and will track thermally. The wide common mode range includes the negative rail, facilitating single supply applications. It is possible to have a "ground based" input driving a single supply amplifierwith ground acting as the second or "bottom" supply of the amplifier. To maintain stability, output snubber networkshave been internally connected to each op amp output (see "amplifier stability" in the attached application notes).The output stage is also current limit protected to approximately 3.0 amps. The MSK 105 is packaged in a spaceefficient 18-pin ceramic dip. Consult factory for other packaging options if desired.

All Ceramic CapacitorsSurface Mount MagneticsMIL STD 461C CR03 (DC-DC Converters)80 Volt Input Transient TolerentWide Supply Range - 16V to 50VHigh Isolation - 500VHigh Power Density - 17WinOutput Voltage Adjustment - StandardRemote ShutdownOperates to 14V Input at 10WAvailable with 3.3V, 5V, 12V and 15V OutputsContact MSK for MIL-PRF-38534 Qualification Status The BBF2800S series of DC-DC converters provides the ruggedness, reliability and features required tomeet the advanced design challenges of today's hi-rel market. This has been accomplished using a packagehaving very low thermal gradients, excellent hermeticity and high voltage isolation. The use of advanced substrateand reflow soldering techniques during construction results in a rugged, cost-effective pin solderable package.The BBF2800S hybrid converter series utilizes all ceramic capacitors and surface mount magnetics to providereliable operation at all operating temperatures while surviving very high G forces.BBF2800S series standard features include kelvin sense, indefinite short circuit protection, remote shutdown, output fault monitoring, turn on voltage point adjustment, switching frequency synchronization of up to 3 units usingno external components and pi-network input filtering. An output voltage adjustmentload compensation pin is alsostandard.Fault tolerance design protects these converters from most external circuit faults. The output and output adjustpins will withstand +35V while the shutdown and all synchronization pins will withstand +50V protecting theconverters from a variety of system or board faults, i.e. solder bridges, etc. Unique load fault protection circuitryallows this converter to pull up loads having difficult static load line characteristics and allows short term loadexcursions significantly beyond ratings in most applications.The BBF2800 series is a current mode push-pull topology converter which operates at a switching frequency of500KHz. Internal filtering of both input and output eliminates the need for external capacitors in many applications.The 12-pin power dip package allows connection to a heatsink and is hermetically sealed and isolated from theinternal circuits.

Manufactured using Space Qualified RH1009 DieRadiation Hardened to 100 Krad(Si) (Method 1019.8 Condition A)Wide Operating Current RangeMaximum Initial Tolerance: 0.2%Excellent Temperature StabilityAvailable in Straight or Gull Wing Lead FormContact MSK for MIL-PRF-38534 Qualification StatusThe MSK 110RH is a dual 2.5V radiation hardened shunt regulator diode with an excellent initial voltage tolerance of5mV and very good stability over temperature. This voltage reference features a wide current range and a low dynamicimpedance that is maintained over the full temperature range. The adjustment terminal allows the reference voltage to beadjusted to compensate for system errors. The MSK 110RH is a hermetically sealed surface mount ceramic package withoptional straight or gull wing lead form.

Operates In Class AB Or Class C ModeLow CostHigh Voltage Operation : 150VLow Quiescent Current : 8.0 mA Total Typ. In Class "C" ModeHigh Output Current : 5A Min. Per AmplifierNo Second BreakdownHigh Speed : 27VS Typ.External Compensation For Optimum Gain-Bandwidth The MSK 101 is a dual high power monolithic MOSFET operational amplifier ideally suited for high power amplificationand magnetic deflection applications. With a total supply voltage rating of 150 volts and 5A of output currentavailable from each amplifier, the MSK 101 is also an excellent low cost choice for motor drive circuits. The MOSFEToutput frees the MSK 101 from secondary breakdown limitations and power dissipation is kept to a minimum with atypical quiescent current rating of only 8.0 mA total in class "C" mode. Power saving class "C" mode is enabledby the user externally. The MSK 101 is packaged in a hermetically sealed 18 pin ceramic dip which has two externalcompensation pins for each amplifier.

Single Supply Operation From 10V to 45VReplaces NHDH0008'And' Input Logic With ExpanderExternal Transition Time ControlOutput Current to 3A PeakAvailable to DSCC SMD 5962-87617The MSK 0008 is an integrated high voltage, high current driver designed to accept standard DTL or TTL logiclevels and drive a pulsed load of up to 3A at 28V. AND inputs are provided along with an Expander connection, shouldadditional gating be required. The addition of an external capacitor and resistor provides control of the rise and falltimes of the output. The device is packaged in a hermetic 10 pin can.