Hose Pipes #5216728

A reinforced silicone rubber tubing for high pressure applications over a wide temperature range. Suitable for continuous operation at temperatures from -80 to 300F (-60 to 150C) and for intermittent exposure up to 350F (180C). Chemically stable and suitable for use with many acids and alkalis. Resistant to ozone, UV and corona discharge. Electrically insulating with dielectric strength 500 Vmil. Inherently low flammability and low smoke. No harmful toxic or physiological effects (RoHS and REACH compliant). Natural translucent silicone tubing is compliant with FDA 21 CFR 177-2600 for use in food contact applications. Many colors can also be formulated within FDA requirements.

A high temperature silicone elastomer reinforced with expandable polyester fabric for use with cured-in-place pipe repair systems. The hose CIPHose is inflated against the repair liner, which is impregnated with resin. The resin cures under the influence of heat to repair the damaged pipe wall and the hose is then withdrawn from the pipe. Silicone rubber C-I-P hose is suitable for use at temperatures up to 300F (150C), and so can be inflated with hot water or with steam for rapid cure cycles. The hoses can be reused because of their good resistance to abrasion and high temperatures. They are very flexible and conform well to pipe bends and joints, leaving a smooth finish to the inside of the repaired pipe. Availability Standard size range with single-ply polyester reinforcement for pipe sizes from 4 inch (102mm) to 24 inch (610mm) diameterAvailable for pipe sizes from 28 inch (711mm) up to 40 inch (1016mm) with double-ply reinforcement.Special sizes on request.T and Y sections can be fabricated in the same material for repairing pipe branches.Standard color is red but other colors are available on request.

A high temperature silicone elastomer reinforced with expandable polyester fabric for use with cured-in-place pipe repair systems. The hose CIPHose is inflated against the repair liner, which is impregnated with resin. The resin cures under the influence of heat to repair the damaged pipe wall and the hose is then withdrawn from the pipe. Silicone rubber C-I-P hose is suitable for use at temperatures up to 300F (150C), and so can be inflated with hot water or with steam for rapid cure cycles. The hoses can be reused because of their good resistance to abrasion and high temperatures. They are very flexible and conform well to pipe bends and joints, leaving a smooth finish to the inside of the repaired pipe.

A reinforced silicone rubber tubing for high pressure applications over a wide temperature range. Suitable for continuous operation at temperatures from -80 to 300F (-60 to 150C) and for intermittent exposure up to 350F (180C). Chemically stable and suitable for use with many acids and alkalis. Resistant to ozone, UV and corona discharge. Electrically insulating with dielectric strength 500 Vmil. Inherently low flammability and low smoke. No harmful toxic or physiological effects (RoHS and REACH compliant). Natural translucent silicone tubing is compliant with FDA 21 CFR 177-2600 for use in food contact applications. Many colors can also be formulated within FDA requirements. Availability Standard range normally available from stock: 70-80ShA, natural translucent inner tubeBraided polyester multi-filament yarn reinforcement60ShA, natural translucent top coatingInside diameter .063 inch (1.6mm) to 1 inch (25.4mm)Also available, subject to minimum order: Supplied cut to lengthAlternative hardness specifications for hose wall and top coatingInside diameter up to 2 inch (50.8mm)USP Class VI for medical and pharmaceutical applicationsFlame retardant materialElectrically conductive materialHigh temperature grade suitable for intermittent use up to 570F (300C)Low temperature grade suitable for use at -100F (-73C)Platinum cured formulationsFormulations suitable for NSF submissionAlternative reinforcementsPolyester monofilament for slightly higher pressure resistance and better resistance to hose kinking at a small bend radius.Glass fiber for higher temperature resistance, up to 570oF (300oC) intermittent exposure (but not recommended for dynamic or high frequency pulsating pressure applications).Aramid fiber for dynamic applications up to 570oF (300oC) intermittent exposure.Stainless steel, copper or other thermal or electrical conducting materials.Special color matchesIndividual customer specifications