Our Complete range of products are RailQor DC-DC Converters, BusQor DC-DC Bus Converters, CF Grade Isolated DC-DC Converters, Dual Output Isolated DC-DC Converters and NiQor Non-Isolated DC-DC Converters.
The RailQor® line Series DC-DC converters is designed to provide isolated dc power in the transportation industry for such electronics as LED displays, audio amplifiers, safety monitors, lighting, and communications systems under the European Standard EN 50155. These converters use SynQor's synchronous rectifier based technology to achieve extremely effiicient industry leading performance. Due to the difficult environmental conditions the transportation market poses on power supplies, SynQor has designed the RailQor line for optimal performance in the most demanding applications.
The BusQor® bus converter are the next-generation, board-mountable, isolated, fixed switching frequency DC-DC converters that use synchronous rectification to achieve extremely high conversion efficiency. The BusQor® bus converters are available in Un-regulated, Semi-regulated, Fully-regulated and High Input Voltage models. The SynQor bus converters are ideal for creating the mid-bus voltage required to drive standard point-of-load (non-isolated) DC-DC isolated converters.
The CFQor series of Quarter-Brick DC-DC converters are high efficiency converters designed for those medical applications that require isolation and leakage current levels that comply with IEC60601-1 for CF patient contact and are also defibrillation proof.
Single and dual output DC-DC converter are composed of next-generation, board-mountable, isolated, fixed switching frequency DC-DC converters that use synchronous rectification to achieve extremely high power conversion efficiency. The power dissipated by the converter is so low that a heatsink is not required, which saves cost, weight, height, and application effort. All of the power and control components are mounted to the multi-layer PCB substrate.
The NiQor® DC-DC converter is a non-isolated buck regulator, which employs synchronous rectification to achieve extremely high conversion efficiency. The NiQor family of converters are used predominately in DPA systems using a front end DC-DC high power brick (48Vin to low voltage bus). The non-isolated NiQor converters are then used at the point of load to create the low voltage outputs required by the design. The wide trim module can be programmed to a variety of output voltages through the use of a single external resistor.
The high input voltage NiQor® family of DC-DC converters offer a unique solution for converting high-powered, variable voltages to a wide range of output voltages. The converter is a non-isolated buck-boost regulator, which employs synchronous rectification to achieve extremely high conversion efficiency. Suitable for use in IBA or to provide a regulated output voltage from a battery source or other variable voltage source. Can be configured to Buck the input voltage down or Boost the input voltage up using a single external resistor.
The AcuQor AC-DC power supply family operates over a universal input range of 85-264Vrms and 47-63Hz making it suitable for World-Wide deployment. Active Power Factor Correction is incorporated to a level >0.98 enabling compliance with IECEN61000-3-2. Single and Triple outputs of 48V, 36V, 28V, 24V, 15V or 12V are available to facilitate the use of Distributed Power Architectures and battery backup, and to directly drive components such as fans, motors, pumps, lamps and actuators.
The IQ65033QM10, IQ65033QGA12, and IQ665033QTA14 iQor™ Power Interface Modules integrate all features required by the AdvancedTCA Base Specification for a frame board power entry into a Quarter-Brick footprint. Minimal external components are required for all the key functions (see applications drawing below). Efficient utilization of hold-up capacitance with adjustable high-voltage management. Available in standard module or full-feature with I2C interface.
The PFCQor Power Factor Correction module is an essential building block of an AC-DC power supply. Used in conjunction with a hold-up capacitor, SynQor's high efficiency DC-DC converters and SynQor's AC line filter, the PFCQor will draw a nearly perfect sinusoidal current (PF > 0.99) from a single phase AC input.
The MultiQor Plate power supply is designed to meet MIL-STD-704, MIL-STD-1275, DEF-STAN 61-5 and MIL-STD-461 when using Military COTS converters for 28Vin system and continuous full power operation is only needed down to 16Vin*. Total output power is 1200W* with typical efficiency up to 95%. Operational features include optional internal EMI filter with ceramic stabilizing bulk capacitor, spike and surge protection, high efficiency reverse polarity protection, no minimum load requirements and soft-start of all outputs. Several optional features are available including cabling accessories (click here).
SynQor provides EMI filters for the InQor series DC-DC converters. All EMI filters provide >80dB differential mode attenuation and >36dB or >60dB common mode attenuation (model dependent) and include stabilizing bulk capacitors and damping resistors.
The InQor® Series is composed of next-generation, board-mountable, isolated, fixed switching frequency DC‑DC converters that use synchronous rectification to achieve extremely high power conversion efficiency. Each module is supplied completely encased to provide protection from harsh environments.