Anchors Unlimited, Inc.

United States


  • Adhesive Installation Accessories

    Adhesive installation accessories are designed to provide a dispenser or mixing nozzle extension when required and to aid in the preparation of the anchor hole.

    View Details » Send Enquiry »

  • Anchor Seal Plugs

    Anchor seal plugs are designed for use with anchor installations in ceilings and wall applications. The plugs help retain the adhesive in the anchor hole and hold the anchor rod centered in the hole until the adhesive sets. The plugs are described by the anchor rod diameter they are used with.

    View Details » Send Enquiry »

  • assemblies

    Assemblies are combinations of drive pins and stamped steel clips designed for specific applications. The pins are held within the clip using either a dome mechanism or a metal top hat. For applications suspending acoustical ceiling systems or light fixtures, several styles of angled clips ...

    View Details » Send Enquiry »

  • Ballistic Point Drive Pins

    Premium drive pins with a 0.300 diameter head have a specially designed point to allow more consistent penetration into harder base materials. Will reduce failures in dense concrete and steel. Drive Pins are manufactured with a 0.150" diameter shank in various lengths. A plastic flute is mounted ...

    View Details » Send Enquiry »

  • Bantam Plug Plastic Anchors

    The Bantam Plug™ anchor is a plastic anchor designed for use with lightweight fixtures with a sheet metal or wood screw. The anchor is recommended for light duty static applications where holding power is not a critical factor. It should not be used overhead.

    View Details » Send Enquiry »

  • Bent Threaded Rod

    Rod is pre -bent at a 22 12 degree angle and includes nuts and washers. Discontinued item once current stock exhausted.

    View Details » Send Enquiry »

  • Brushes

    Adhesive installation accessories are designed to provide a dispenser or mixing nozzle extension when required and to aid in the preparation of the anchor hole.

    View Details » Send Enquiry »

  • carbide drill bits

    SDS-Max® Carbide Drill Bits are designed for use in a rotary hammer equipped with a SDS Max® type chuck. The bits are manufactured to conform with ANSI Standard B212.15 and can be used to drill in concrete, block, brick, and soft stone. The new Y-Cutter head design has three main cutters in a "Y" ...

    View Details » Send Enquiry »

  • Cartridges

    AC100 Plus Epoxy Acrylate is a two-component high strength structural adhesive used to bond threaded rod and reinforcing bar into solid concrete and masonry base materials. The adhesive system can also be used to anchor into hollow masonry materials using screen tubes. The AC 100 Plus adhesive is a ...

    View Details » Send Enquiry »

  • Concrete Auger Bits

    Concrete auger bits are a one piece unit designed for use in a rotary hammer equipped with a Spline or SDS-Max® chuck. The efficient design of these bits provides faster drilling with reduced vibration and noise. They are ideal for producing larger diameter, deep holes and are best suited for ...

    View Details » Send Enquiry »

  • Deck Screws Roofing Screws

    Deck Screws™ are designed for attaching rigid insulation board, single ply membrane, and wood blocking to steel and wood decks. Some sizes can also be used in concrete decks. Available sizes include No. 12, No. 14, and No. 15 diameters in carbon steel with either hex washer or Phillips-style ...

    View Details » Send Enquiry »

  • EIFS Pin

    EIF5 Pins with a 0.300 diameter read 1-12" length are designed for permanently fastening to concrete or concrete block, installation systems such as, waterproofing membranes, plastic sheeting, metal lathe and wire mesh for plaster and stucco systems. To provide resistance to pullover, ...

    View Details » Send Enquiry »

  • Epoxy

    T308+ is a two-component epoxy adhesive anchoring system. The system includes injection adhesive in plastic cartridges mixing nozzles, dispensing tools and hole cleaning equipment. The T308+ is designed for bonding threaded rod and reinforcing bar into drilled holes in concrete base ...

    View Details » Send Enquiry »

  • Epoxy Injection Adhesive Anchoring System

    The PE1000+ is a two-component, high strength adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing nozzles, dispensing tools and hole cleaning equipment. The PE1000+ is designed for bonding threaded rod and reinforcing bar hardware into drilled holes in ...

    View Details » Send Enquiry »

  • Fluted Plastic Anchors

    The Fluted Plastic Anchor is designed for light duty fastening applications with sheet metal or wood screws. Longitudinal ribs on the anchor body prevent it from turning during tightening of the screw. This inexpensive plastic screw anchor comes color-coded by diameter for easy application. The ...

    View Details » Send Enquiry »

  • Forming Pins

    For concrete forming applications, the 1-34" (44mm) pin is designed for fastening wood members up to 34" in thickness while the 2-12" (62mm) pin is designed for wood members up to 1-12" in thickness. The pin has a break off groove 1" from te point to allow the wood forming members to be easily ...

    View Details » Send Enquiry »

  • Hammer Drive Pins

    Hammer Drive® pins are designed for permanently fastening a fixture to concrete and some types of masonry. This fastener is designed for use in a standard hand tool and should not be used in a powder actuated tool. The pins are formed with a 14" diameter head on one end and a 0.140" diameter ...

    View Details » Send Enquiry »

  • Head Drive Pins

    Drive pins with a 0.300 diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured with a 0.143" diameter shank in various lengths. Knurled shank designs are available to increase performance in steel base ...

    View Details » Send Enquiry »

  • Heavy Duty Chisels

    Heavy Duty Chisels and accessories are designed for use in a combination rotary hammer chipping tool equipped with a Spline, SDS-Max®, or 34" Hex chuck. The chisels can be used for chipping applications in concrete, block, brick, and soft stone.

    View Details » Send Enquiry »

  • Heavy Duty Core Bits

    Heavy Duty Core Bits are designed for use in a rotary hammer equipped with a spline or SDS-Max® type chuck. The bits can be used to drill in concrete, block, brick, and soft stone. One piece core bits are packaged with a centering bit and ejector pin.

    View Details » Send Enquiry »

  • Heavy Duty Straight Shank Bits

    Heavy Duty Straight Shank Carbide Bits are designed for use in a hammer drill equipped with a 3 jaw Jacobs type chuck. The bits meet ANSI standards and can be used to drill in concrete, block, brick, and soft stone.

    View Details » Send Enquiry »

  • Industrial Grade Straight Shank Drill Bits

    Industrial Grade Straight Shank Carbide Bits are designed for use in a hammer drill equipped with a 3 jaw Jacobs type chuck. The bits meet ANSI standards and can be used to drill in concrete, block, brick, and soft stone.

    View Details » Send Enquiry »

  • LEGS Hollow Wall Anchors

    The LEGS® anchor is a fast, easy to use expansion anchor designed for use in wallboard. The anchor has a pierce point, requiring no pie-drilling. Removal of the anchor, if required, is easy. Once removed, the anchor leaves a small slit in the wallboard.

    View Details » Send Enquiry »

  • Plastic Screen Tubes

    The nominal diameter of the screen listed indicate the matching rod diameter. Note that hole size required for plastic screen tubes are different than that for the stainless steel tubes.

    View Details » Send Enquiry »

  • Plus Carbide Drill Bits

    Quatro Head SDS-Plus® Carbide Drill Bits are designed to reduce vibration up to 60% and noise up to 30%. These bits produce rounder and more accurately located anchor holes.

    View Details » Send Enquiry »

  • Plus SDS Carbide Drill Bits

    SDS-Plus® Carbide Drill Bits are designed for use in a rotary hammer equipped with an SDS (slotted drive shaft) type chuck. The bits are manufactured to conform with ANSI Standard B212.15 and can be used to drill in concrete, block, brick, and soft stone. As existing stock of the single tip ...

    View Details » Send Enquiry »

  • Polly Hollow Wall Anchors

    The Polly™ is a sleeve type hollow wall anchor designed for use in base materials such as plaster, wallboard, concrete block, hollow tile or plywood.

    View Details » Send Enquiry »

  • Poly-Toggle Plastic Hollow Wall Anchors

    The Poly Toggle™ is a screw actuated hollow wall anchor for use in paneling, wallboard and solid masonry available in 6 sizes to match the most common wall thicknesses. In solid base materials, the anchor can be used by removing the outer wings. The performance of this product depends on the ...

    View Details » Send Enquiry »

  • Pop-Toggle Fasteners

    Pop-Toggle™ fasteners are hollow wall anchors ideal for static applications requiring light to medium load performance. Installation is very fast, needing a pre-drilled 516" diameter hole. The fastener pre-install without a screw, allowing for easy placement and removal of the fixture. ...

    View Details » Send Enquiry »

  • Power-Bond Pump

    The Power-Bond® Pump consists of a self contained 10 fluid ounce pump style cartridge in which the adhesive components are mixed. A standard manually operated caulking tool can be used in the installation of threaded rod in solid concrete.

    View Details » Send Enquiry »

  • PowerFoam aircraft exterior spray

    Powerfoam and TriggerFoam are one-part polyurethane expanding foams that set and cure into their final form by reacting to moisture and humidity present in the air. Their exceptional ability to bond allows Powerfoam and TriggerFoam to be applied to various building elements including the surfaces ...

    View Details » Send Enquiry »

  • Powerlite fastener

    The Powerlite™ is a fastener used to mechanically attach rigid insulation board and single-ply membrane to structural cement wood fiber, gypsum, and lightweight insulating concrete roof decks. The fastener is used in conjunction with insulation and membrane stress plates. The plates are ...

    View Details » Send Enquiry »

  • powers tools

    Hammer actuated, professional grade powder actuated tool. Engineered for high reliability, low maintenance and speed. This tool uses four levels of power; grey through yellow loads (levels 1-4) and 300, 8 mm head fasteners with lengths of 12" through 3" and 14"-20 threaded studs.

    View Details » Send Enquiry »

  • Powers Track-It Tools

    Trak-lt® Fasteners and Blue Nailer-Gas Fuel Cells are designed to be used with the Powers Trak-It® Tool and can also be installed with the ITW Ramset® TrakFast® tool. Ten fasteners are collated on each patented, plastic top hat-style strip. Use for light duty static applications such as drywall ...

    View Details » Send Enquiry »

  • PTZ Powder Actuated Fasteners

    The Powers PTZ Powder Actuated Fasteners are designed for fastening through pressure treated lumber into concrete and grout filled masonry The fasteners are manufactured to provide a minimum level of corrosion resistance equivalent to triple zinc coatings (G-185) found on connector hardware ...

    View Details » Send Enquiry »

  • Rebar Cutter Bits

    ebar cutter bits provide a quick, easy method for drilling through mesh or reinforcing bars embedded in concrete when the drilled hole cannot be relocated. The bits are used in the rotation only mode and are designed to fit in a standard rotary drill motor with a 12" Jacobs style ...

    View Details » Send Enquiry »

  • Rotary Carbide Drills

    Rotary Carbide Bits are designed for use in a rotation only drill equipped with a 3 jaw Jacobs type chuck. The bits meet ANSI standards with a positive rake tip and can be used to drill in soft or brittle masonry materials using rotation only. Fast spiral flutes are for fast drilling in soft to ...

    View Details » Send Enquiry »

  • Safety Strip

    The safety strip is molded in a special length to provide a visual indication that the tool is loaded. 0.27 Caliber Safety Strip® for Powers P3500, PA3500, PA351, P3600, Ramset® SA270, Viper, Hilti® DX36M, DX451 and DX460

    View Details » Send Enquiry »

  • Scru-Lead Anchors

    The Scru-Lead™ anchor is designed for use with sheet metal or wood screws in concrete, block or brick. The anchor is made entirely of lead alloy which is soft enough for easy installation, yet hard enough to give sure, secure holding power. The performance of this product depends on the integrity ...

    View Details » Send Enquiry »

  • Spline Carbide Drill Bits

    Spline Carbide Drill Bits are designed for use in a rotary hammer equipped with a spline type chuck. The bits are manufactured to conform with ANSI Standard B212.15 and can be used to drill in concrete, block, brick, and soft stone. Both Y- Cutter and single tip head styles are available.

    View Details » Send Enquiry »

  • Stainless Steel Screen Tubes

    Screen tubes are made from a 300 series stainless steel. The nominal diameter of the screen listed indicates the matching rod diameter.

    View Details » Send Enquiry »

  • Steel Drive Pins

    50232, Type 316 SS 0.300 Head Pin with 78" Washer316 Stainless Steel Pins provide a maximum level of corrosion resistance.

    View Details » Send Enquiry »

  • Steel Wedge-Bolt Screw Anchors

    The 316 SS Wedge-Bolt screw anchor is specifically engineered for exterior applications where high corrosion resistance is needed, withstanding the most demanding conditions. With the corrosive resistant properties of 316 SS, the anchor can be used in waste and water treatment plants, food and ...

    View Details » Send Enquiry »

  • Stick-E Accessories

    Stick-E Accessories snap directly in the nose of the Trak-lt Tool and are held in place while shooting.

    View Details » Send Enquiry »

  • Strap-Toggle Hollow Wall Anchors

    The Strap-Toggle™ is a pre-assembled anchor consisting of a carbon steel wing and a locking cap ratchet leg assembly molded from engineered plastic. When compared to traditional toggles, this unique anchor can be installed through a smaller hole and does not require a fixture or screw to set it.

    View Details » Send Enquiry »

  • Stress Plates

    Stress plates are designed for use with Deck Screws™, SPIKE® anchors, and Speed Lock toggles. Stress plates can be grouped into two categories; insulation plates and membrane plates. Insulation plates, as the term implies, are used when mechanically attaching rigid foam insulation to roof decks. ...

    View Details » Send Enquiry »

  • Taper Drill Bits

    "A" Taper Drill Bits are designed for use in a rotary hammer equipped with an "A" Taper type chuck. The bits meet ANSI standards and can be used to drill in concrete, block, brick, and soft stone.

    View Details » Send Enquiry »

  • Tapper Concrete Screw Anchors

    The Tapper™ Anchoring System is a family of screw anchors, specially designed drill bits and installation tools designed to meet the needs of most light to medium duty applications in concrete, block and brick. The Tapper™ concrete screw anchor is produced in either Hex washer head or Phillips ...

    View Details » Send Enquiry »

  • Tapper Drill Bits

    Tapper™ Drill Bits in the diameters listed are nominal size. 316" and 14" Perma-Seal™ Tapper™ anchors must be installed with special tolerance Tapper™ drill bits. 14" Stainless Steel Tapper™ anchors require the use of specific tolerance Tapper™ drill bits, which are gold or silver ...

    View Details » Send Enquiry »

  • Threaded Studs

    Threaded studs are available in 14"-20 and 38"-16 thread diameters with a variety of thread and shank lengths for use in concrete, some types of masonry, and A36 structural steel. They are used for applications where it may be desirable to remove the fixture, where shimming may be required. ...

    View Details » Send Enquiry »

  • Tilt Wall Wedge-Bolt Anchors

    Ideal for brace shoes used to support tilt up wall panels. The NEW Powers Tilt Wall Wedge-Bolt anchors are specifically engineered for high load Tilt-up applications.

    View Details » Send Enquiry »

  • toggle bolts

    The Toggle Bolt is a spring wing type hollow wall anchor designed for use in block, wallboard and other hollow base materials. The Toggle Bolt is a two-part assembly consisting of a machine screw and a spring wing toggle. Sizes range from 18" x 2" to 12" x 6" with combo round, flat, mushroom, ...

    View Details » Send Enquiry »

  • TriggerFoam aircraft exterior spray

    Powerfoam and TriggerFoam are one-part polyurethane expanding foams that set and cure into their final form by reacting to moisture and humidity present in the air. Their exceptional ability to bond allows Powerfoam and TriggerFoam to be applied to various building elements including the surfaces ...

    View Details » Send Enquiry »

  • Triggerfoam Tools

    Powerfoam and TriggerFoam are one-part polyurethane expanding foams that set and cure into their final form by reacting to moisture and humidity present in the air. Their exceptional ability to bond allows Powerfoam and TriggerFoam to be applied to various building elements including the surfaces ...

    View Details » Send Enquiry »

  • Wall-Dog Anchors

    The Powers Wall-Dog™ is the industry's first ail steel one-piece screw anchor, which features high-profile threads for easy fastening into wallboard and other masonry base materials. Its deep cutting, corkscrew-like threads provide for smooth entry and a powerful hold, and when removed the ...

    View Details » Send Enquiry »

  • Wedge-Bit Anchors

    For proper performance, the Wedge-Bolt anchors must be installed with a Wedge-Bit. The Wedge-Bit has a special matched tolerance range designed to provide optimum performance for the anchor.

    View Details » Send Enquiry »

  • Wedge-Bolt Anchors

    The Wedge-Bolt® anchor is a one piece heavy duty anchor with either a finished hex head or countersunk Phillips flat head. It is easy to identify, removable and vibration-resistant.

    View Details » Send Enquiry »

  • Wedge-Bolt Orange

    The Carbon Steel Wedge-Bolt OT screw anchor is a specifically engineered part for the racking industry. This unique and universal anchor is available in a finished hex head design and can be easily installed with either an impact wrench or conventional hand socket. This anchor, unlike Blue tip ...

    View Details » Send Enquiry »

  • Zip-It Anchors

    The Zip-It® anchor is a one piece self drilling anchor designed for use in hollow gypsum wallboard for light duty loads. It is available in both engineered nylon and Zamac alloy for use with either a No. 6 or No. 8 screws in 38" to 1" wallboard. The Zip-It® Jr. is formed from engineered nylon for ...

    View Details » Send Enquiry »

  • Zip-Toggle Hollow Gypsum Wallboard Anchors

    The Zip-Toggle™ is a hollow gypsum wallboard anchor designed to provide superior performance without the need to pre -drill larger diameter holes. The Zip- Toggle™ is packaged with its own No. 6 x 2' ' lubricated screw.

    View Details » Send Enquiry »


Search


Contact Details

Verona, PA 15147 map, , United States

View Mobile No.