The AP10, Absolute Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full-scale output of 40 mV per volt at 3kHz. The unit operates with more...
Material : Zinc Alloys (Zamak #3 and Zamak #5), Aluminum Alloys (A380, A384, A356 and 6063) and Magnesium Alloys (AZ-91D).
Die Casting products that AST supply includes Vehicle die casting parts, Pneumatic Power Tool die casting components, Lamp industries die casting parts and general die casting mechanical components.more...
Using our advanced CNC turning and grinding operations, Signal Machine Company performed the final machining of a fairly large cast iron casting ring supplied by the customer. Meeting a precision (+-) .01 of an inch precision tolerance, we machined the part to measure approximatemore...
Materials Of Construction : Carbon steel, 316 Stainless Steel
Red Valve Series 40 Pressure Sensors are the industry standard for protecting instrumentation. They assure accurate, dependable pressure measurement of slurry and corrosive fluids. The line pressure is sensed 360° through the flexible rubber sleeve. The captive fluid is displacemore...
Wrex Products, Inc. Die Casting Department converts over 50, 000 lbs. of aluminum and zinc ingots into product each month. Aluminum and zinc alloy die castings are an attractive alternative to other materials. By using the natural properties found in these alloys, the extra cost more...
We are offering pressure vessels. Pressure vessels are designed to operate safely at a specific pressure and temperature, technically referred to as the “design pressure” and “design temperature”. A vessel that is inadequately designed to handle a high pressure constitutemore...
Trueblood offers a full range of ISO 9001:2008 certified die casting capabilities: Aluminum & zinc die castings Miniature, small & medium sized castings Complete secondary & CNC machining operations In-house die design, engineering & CAD In-house tooling with full service tool romore...
Material: Aluminum Magnesium and Zinc Press Size: 12 ton to 3000 ton Part weight: 5 grams to 35 kg Secondary Operations: CNC, Drilling Tapping, sanding , polishing, trim press, shot blasting and more Finish: Chrome free passivisation, Teflon coating, ceramic coating, polishing, wmore...
J.F.D. Tube & Coil Products, Inc. has been manufacturing tanks since 1983. We build all of our tanks to order. All tanks and pressure vessels are built in accordance with section VIII, division 1 of the A.S.M.E. code. They come certified with either our "U" or "UM" stamp and Natimore...
At American Precision Services we were contracted by a customer in the Nash pump industry to provide custom wire manufacturing services. The project required the fabrication of expanding outer flange castings as highlighted below. Employing our CNC lathe and mill, we implemented more...
New England Keyboard, Inc. offers a variety of casting methods and materials to guarantee you the most cost effective approach based on individual applications. Part size, complexity, surface finish, and production lot size determine the method to be used. Complete, state-of-the-more...
In March of 2014, Industrial Innovations purchased Advance Products Corporation’s Automation division. Under the newly-formed Advance Automation LLC, we continue to offer reciprocating die sprayers, spray manifold technology, robot extractors, and servo ladlers at our newly refmore...
Die Cut Parts includes gaskets, insulation, and other industrial parts. We fabricate many kinds of foam as well as rubber, silicone, neoprene and other materials. more...
We are offering cast electrical component. With over 30 years of experience in the thermoset plastics industries, crosslink provides customized epoxy and polyurethane formulations, cast components, and a high level of industry expertise to ensure that our customers are successfulmore...
Aside from using trim dies, the usual method of degating is to tumble in an open mouth oblique barrel then screen separate the parts. Working with small pieces in very large barrel tumblers means a densely packed load that is too heavy to move easily and has poor flow properties.more...
Utilize Casting Techniques Corporation as your one-stop aluminum and zinc die casting source for the Northeast United States. We serve a wide variety of manufacturers as a single source for everything from initial engineering design assistance to machining and finishing. more...
3L Filters™ has over 40 years of experience in the design and fabrication of tanks and pressure vessels. Our engineering group can perform complete stress and seismic analysis and design registration. 3L Filters™ has registered Quality Assurance Programs for nuclear… more...
With a long history of providing Vessels, Chambers, and Containment Storage to customers of various disciplines, AET is well versed in meeting customer specifications. Our Weld Shop and Machine Shop being in the same location helps to expedite the manufacturing process. Certifiedmore...
Custom Engineering has built unfired pressure vessels for virtually any industry; from CO2 to Nitrogen, from Air to Water. All Custom Engineering Pressure Vessels are built and tested in accordance with the A.S.M.E. Boiler and Pressure Vessel Code Section VIII Division I for unfimore...
Zinc hot chamber die casting machines ranging in size from 250 ton to 500 ton produce castings for a broad variety of industrial market sectors: Metering and Control Devices Lawn and Garden Commercial Lighting General Engineered Die Castings Power and Hand Tools Conventional zincmore...
Welded pressure vessesl and tanks from lab scale to 500 gallons Pressures from 15 to 5, 000 psi for welded vessels, and to 60, 000 psi for forged vessels Materials including Carbon Steel, Stainless Steel, Nickel-based Alloys, and other machinable, weldable alloys Closures selectemore...
Cir-Q-Tek has extensive knowledge and capabilities to be your first choice for machined, finished, heat treated, or assembled castings. Our engineering and production team will work from your specifications and develop a process for producing quality parts within your budget. Ourmore...
COMPONENTS A range of parts for thousands of applications – made in house Superior Die Set Corporation is, and has always been, a manufacturer of components for the metal stamping die, plastic injection mold, die cast, and forging industries. In addition to an offering of standmore...
Gravity die casting is a terminology used usually outside the United States to describe the Permanent Mold process. There is no difference between the processes. more...
In order to ensure zero defects at buyer's end, we make sure that we conduct stringent quality procedures. We have hired only professional packaging personnel who have experience and expertise in this domain. They make use of the finest quality packing material to ensure zero dammore...
We custom build die casting and injection tooling (including Trim Dies), used in the manufacture of metallic and non-metallic components. Our tooling division can make dies for components of varied sizes and materials. For instance, our tools have been used in the manufacture of more...
Embossing is the process of placing a flat part in between a male and female embossing die set. Once the part is pressed by the male and female dies, the image or characters are raised above the level part, similar to the numbers on a credit card. Sharpen your dull, worn-out diesmore...
This Component Finder will make it easier for you to search for generic pressure sensors that can be used for general measurements in research and development or in test laboratories. As well as generic pressure sensors, Kistler offers a vast range of customized solutions for premore...
PDC constructs stirred reactors and pressure vessels from most machinable alloys. Capacities range from 50 cc to 500 gallons (2 m3). Agitated reactor design pressures range from full vacuum to 150, 000 psig (10, 300 barg). Temperatures range from -400 °F to 2, 500 °F ( -200 °Cmore...
Advanced Gasket specializes in custom die cutting. We die cut non-metallic gaskets and components from a wide range of materials, which allows us to satisfy all of your gasket design requirements. Our experienced technicians have the knowledge of materials and the die cutting promore...